Nissan Skyline R32 oil pan, oil pump and oil strainer removal and installation
 
Tools required
Seal cutter KV101 11100
Oil seal drift KV401 00900
Tube presser WS3993
 
Nissan Skyline GT-R32 oil pan, oil pump and oil strainer removal and installation
 
Additional work required:
•  Engine ASSY removal and installation
•  Engine oil draining and refilling
 
Nissan Skyline GT-R32 oil pan, oil pump and oil strainer removal and installation
 
[Point 1] Nissan Skyline R32 oil pan bolt, nut removal and installation
 
Removal
 
•  Remove bolts and nuts in reverse order of installation shown in figure on left.
 
Installation
 
•  Tighten nuts and bolts in numerical order shown in figure on left.
CAUTION:
Make sure there is no dirt, dust or debris on oil pan installation surface.
 
+
 
Nissan Skyline GT-R32 oil pan, oil pump and oil strainer removal and installation
 
[Point 2] Nissan Skyline R32 oil pan removal and installation
 
Removal and cleaning
 
•  Insert seal cutter between cylinder block and oil pan and remove oil pan by tapping seal cutter.
 
Nissan Skyline GT-R32 oil pan, oil pump and oil strainer removal and installation
 
•  Use a scraper to remove all traces of liquid gasket from mating surface.
CAUTION:
(1)  Use a scraper to remove all liquid gasket and seal material attached to cylinder block and oil pan flange groove. Remove all gasket material and other debris that falls into the oil pan.
(2)  Be careful not to scratch oil pan.
•  Clean all contact surfaces with white gasoline or equivalent.
 
Nissan Skyline GT-R32 oil pan, oil pump and oil strainer removal and installation
 
Installation
 
•  Cut off nozzle tip of liquid gasket (KP510 00510) at point shown in figure on left and insert in tube presser.
 
Nissan Skyline GT-R32 oil pan, oil pump and oil strainer removal and installation
 
Installation
 
Apply liquid gasket to inner sealing surfaces as shown in figure. Installation should be performed within 5 minutes after coating.
•  Apply a continuous bead of liquid gasket (KP510 00150) to mating surfaces of oil pan.
 
Nissan Skyline GT-R32 oil pan, oil pump and oil strainer removal and installation
 
•  Apply liquid gasket (KP510 00150) to areas 7 mm (0.28 in) inside from center of oil pan bolt holes. 
CAUTION:
(1)  Be sure liquid gasket application is 4.0 mm (0.157 in) wide.
(2)  Wait at least 30 minutes before refilling engine oil and engine coolant.
 
Nissan Skyline GT-R32 oil pan, oil pump and oil strainer removal and installation
 
[Point 3] Nissan Skyline R32 oil strainer installation
•  When installing oil strainer, make sure O-ring is inserted securely in groove and then install.
 
Tightening torque Nm (kg-m, ft-lb) :
M8 - 16-21 (1.6-2.1, 12-15)
M6 - 6.3-8.3 (0.64-0.85, 4.6-6.1)
 
[Point 4] Nissan Skyline R32 oil pump installation bolts
•  There are 4 types of bolts so be careful not to mistake them when they are installed.
 

Installation position

Length below head mm (in)

Number of bolts

Tightening torque N-m (kg-m, ft-lb)

(1)

20 (0.79)

4

9.0-11.8 (0.92-1.2, 6.7-8.7)

(2)

35 (1.38)

2

9.0-11.8 (0.92-1.2, 6.7-8.7)

(3)

45 (1.77)

1

9.0-11.8 (0.92-1.2, 6.7-8.7)

(4)

55 (2.17)

1

9.0-11.8 (0.92-1.2, 6.7-8.7)

 
Nissan Skyline GT-R32 oil pan, oil pump and oil strainer removal and installation
 
[Point 5] Nissan Skyline R32 front oil seal removal and installation
 
Removal
 
•  Use a screwdriver to remove front oil seal from front cover.
 
Nissan Skyline GT-R32 oil pan, oil pump and oil strainer removal and installation
 
Installation
 
•  Be careful not to scratch or damage oil seal retainer. Use oil seal drift and insert it at same level as front surface of oil pump housing.
•  Apply engine oil or chassis grease to area around oil seal lip.
 
Nissan Skyline GT-R32 oil pan, oil pump and oil strainer removal and installation
 
[Point 6] Nissan Skyline R32 oil leak and oil pressure check
•  After installation, warm up engine and check for oil leaks and proper oil pressure.
•  To perform oil pressure inspection, remove oil pressure switch and attach oil pressure gauge.
 

Engine speed (rpm)

Idling

2,000

6,000

Delivery pressure kPa (kg/cm², psi)

Approx. 147 (1.5, 21)

Approx. 294 (3, 43)

Approx. 451 (4.6, 65)

 
Oil temperature at 80°C (176°F)